Etapa potencia AV Classe Audio Sigma AMP5

Classe Sigma AMP5

Producto Agotado y Descatalogado. No disponible.



Producto con envío gratuito

  • Etapa de potencia multicanal Classe Audio Sigma AMP5. Pensada para poder amplificar hasta 5 altavoces.
    con una potencia de 200 Watios por canal.
    Incluye entradas balanceadas XLR y RCA estéreo.


    Etapa de potencia multicanal Classe Audio Sigma AMP5. Pensada para poder amplificar hasta 5 altavoces.
    con una potencia de 200 Watios por canal. Incluye entradas balanceadas XLR y RCA estéreo.


    Dentro de esta misma serie Sigma encontramos:
    _Procesador Classe Sigma SSP
    _Etapa estereo Classe Sigma AMP2 

    Potencia de salida: 5x200W RMS a 8 ohmios.

    5x400W RMS a 4 ohmios.
    Entradas Balanceadas y No Balanceadas.
    Conexión inteligente con componentes Classé compatibles mediante CAN BUS (RJ45).
    Toma de control RS232 (actualización de software y control).
    Toma USB (actualización de software y obtención de datos).
    Tomas de disparo de 12V.
    Tomas de infrarrojos.
    Dimensiones (An x Al x P): 433 x 95 x 370 mm.
    Peso: 12,7Kg.

    The Sigma series AMP5 is a 200W/Ch five-channel amplifier derived from the AMP2, but with necessary part and layout changes to accommodate its five-channel architecture. Like the AMP2, it utilizes switching technologies for both power supply and amplification stages. A Classé-designed switch mode power supply with Power Factor Correction makes over 1,000W of clean and stable power available while being both compact and efficient. A new class D amplifier topology provides wide dynamic range, smooth and extended frequency response and rich harmonic detail to yield stunning sonic performance. The efficiency of class D adds efficiency, low heat dissipation and relatively small size to the list of the AMP5’s attributes.

    All tests un-weighted and 20Hz – 20kHz measurement bandwidth used.

    Frequency response

    10Hz – 20kHz, -1dB into 4Ω
    Output power

    200W rms into 8Ω All channels driven
    400W rms into 4Ω Any two channels driven*
    Harmonic Distortion

    0.018% @ 1kHz All channelsdriven
    to 1/8th power into 8Ω

    Peak Output Voltage

    116V peak to peak, 58V rms no load
    116V peak to peak, 58V rms into 8Ω
    Input Impedance

    100kΩ Balanced / 50kΩ SE
    Voltage gain

    29 dB
    Input level at clipping

    1.4Vrms Balanced/SE


    >80 dB below fundamental into 8Ω SE

    Signal to Noise Ratio

    -100 dB at peak output into 8Ω (AES17)

    Rated power

    200W @ 1/8th power into 8Ω
    Mains voltage

    100V - 240V, 50/60Hz
    Overall Dimensions

    Width: 17.00” (433mm)
    Depth (excluding connectors): 14.57” (370mm)
    Height: 3.75” (95mm)
    Net weight

    23.1 lb (10.48 kg)
    Shipping weight

    30.0 lb (13.61 kg)
    *each channel supports 400W output into 4 ohms but the AC Mains/power
    supply cannot support all channels driven simultaneously at this level, which
    would require over 2,500W and only occur under a special test condition.
    Every channel easily drives lower impedance loads.

    Classe Sigma AMP5

    16 productos de la misma categoría: